• Home
  • Info
  • Contact Us
  • COMING SOON!!

32 FORD 3 WINDOW COUPE PROJECT Still available!

32 project with title
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
32 FORD 3 WINDOW PROJECT with TITLE Please do check the list in the photos of the parts included and current costs of those item. Remember the many hours involved thus far in this build that I did not put a price on. The list adds up to about $40k. DON'T BE SHY. STOP, TAKE A LOOK AND THROW ME AN OFFER. I'M MOTIVATED TO SELL AND I HAVE OTHERS!! CALL or TEXT TERRY AT 717.514.4350 I purchased parts from various sources and built this coupe to this point. I'm sure I have hundreds of hours in it thus far. BTW, thats a white gelcoat you see, not paint. The engine was bought from a fellow that had it in a very good running 32 roadster. He went Vintage, and installed a flathead. As such, I got the engine, radiator and exhaust. It was stick shift, had a tunnel ram with 2x4s and I replaced that with a new polished intake and Edelbrock carb, along with an AOD automatic trans. 2 sets of valve covers included. See details about engine in parts list below. CHECK ALL THE PHOTOS!Trans is a used unit from a Lincoln that has been fresh performance built and has a new converter, never run. I did not have a driveshaft made for it yet. SPEEDWAY MOTORS GLASS BODY, DOORS, TRUNK HINGED, POWER WINDOWS INSTALLEDBROOKVILLE ROADSTER COMPANY 32 FORD FRAME. TITLED 1932 FORD CP9” 31 SPLINE REAR w NEW CENTER POSI, 370 RATIO, DISC BRAKES, COIL OVER 4-LINKAOD TRANS, FRESH WITH CONVERTER & 68 MUSTANG SHIFTER, (NO DRIVE SHAFT)MID 80s GT MUSTANG 302 W/UPGRADE HEADS & CAM, NEW POLISHED INTAKE/CARBSANDERSON LIMEFIRE HEADERS WITH DONOR UNDER CHASSIS PIPE SYSTEMGRIFFIN BRASS RADIATOR, ELECTRIC FAN, STEEL RAD SHELLCOMPLETE HEAT/AC SYSTEM, CUSTOM SEAT WITH EMBROIDRYTORQUETHRUST D WHEELS, WITH TIRES, 4-1/2” FORD BOLT PATTERNCHROME FRONT SUSPENSION, VEGA BOX, VINTAGE COLUMN, ALL HOOKED UP, DISC BRAKES22 CIRCUIT WIRE HARNESS, GUIDE 682C STYLE HEADLAMPS, CUSTOM TAIL LAMPSNEW 32 STYLE GAS TANK, COVER AND ACCESSORIESI'm Terry, My car lot is in Elizabethtown, Pa.Please do call or text me at 717.514.4350 with inquiries.
SCROLL DOWN FOR: * COMBO metal lathe, mill, drill * LENCO spot welder * DREIS & KRUMP 8' x 14 gauge Metal Brake * NIAGRA 6' x16 Gauge power sheer * 48" WIDE, Dbl door bead blast cabinet * UNIRAM water borne paint gun cleaner * DVORAK SCOTCHMAN iron worker
3 in 1 COMBINATION LATHE/MILLING/DRILLING MACHINE WITH STAND TOOLING AND ACCESSORIES - $1700 SCROLL DOWN
I purchased this new @ Harbor Freight, and used very little. Combo lathe, mill, drill. Lots of tooling, inside & outside chuck jaws. Steel stand with drawers. Lots of specs on photos. Light surface rust on some bare metal parts, "not pitted" New cost for all included approx $3500, My Price $1700 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
gallery
LENCO SPOT WELDER - $550 SCROLL DOWN
Had it many years & always worked well, 230 VOLT, 50 AMP New cost approx. $1500 - My Price $550 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
gallery
gallery
DREIS & KRUMP 8' x 14 GAUGE BRAKE - $2000 SCROLL DOWN
Had this a long time and still in use. Capacity is 8' long, 14 gauge max. Used similar US Made units are prices around $3000, My Price - $2000 Call or Text Terry, 717.514.4350 Elizabethtown, Pa.
gallery
gallery
NIAGRA 72" X 16 GAUGE POWER SHEER - $4000 SCROLL DOWN
Still in use, Never failed me, Still cuts sharp & clean, Keep fingers FAR away! Runs on standard 230 volt single phase, Cap. (6 FT.) 72" wide x 16 gauge max. Similar units are hard to find used and a fortune new. Used 5FT. units everywhere & priced at $4500 & up. My Price $4000 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
gallery
gallery
gallery
gallery
DVORAK SCOTCHMAN IRON WORKER - $3500 SCROLL DOWN
Most used tool in my shop & still in use. Shows wear, but still works fine, Has square 3/4"ish changeable punch die, and no others included. See photos for specs. Standard 230 volt single phase. Many used on web. Most 3 phase Most not priced, but $4500 & up seems about right. My Price $3500
gallery
gallery
gallery
gallery
SANDBLAST CABINET, 48" WIDE, DBL DOOR - $600 SCROLL DOWN
48" Wide, Doors at both ends, Hook shop vac to it for venting. Could use a new glass & some wear parts in gun. Currently still in use. Similar units this big around $2000. My Price $600 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
gallery
gallery
gallery
UNI-RAM WATER BORNE PAINT GUN CLEANER - $400 READ FULL DESCRIPTION PLEASE SCROLL DOWN
Never used this tool. They cost a lot of money. Not sure if it can be used for solvent based paint guns? You see the new cost, so there is lots of $$ room to modify it if a solvent application pump or hoses are needed. My Price $400
gallery
gallery
gallery
BLANK LOT, CHECK BACK!!
BLANK LOT, CHECK BACK!!
Copyright © 2021 Network Solutions, LLC. All rights reserved.

We use cookies to enable essential functionality on our website, and analyze website traffic. By clicking Accept you consent to our use of cookies. Read about how we use cookies.

Your Cookie Settings

We use cookies to enable essential functionality on our website, and analyze website traffic. Read about how we use cookies.

Cookie Categories

Essential

These cookies are strictly necessary to provide you with services available through our websites. You cannot refuse these cookies without impacting how our websites function. You can block or delete them by changing your browser settings, as described under the heading "Managing cookies" in the Privacy and Cookies Policy.

Analytics

These cookies collect information that is used in aggregate form to help us understand how our websites are being used or how effective our marketing campaigns are.