1939 plymouth 2 door sedan Resto-rod Still available!

Small block mopar powered!! LOOKING FOR OFFERS AROUND $12K DON'T BE SHY. GIVE ME A FAIR OFFER! CALL or TEXT TERRY 717.514.4350
MOPAR LOVERS WILL APPRECIATE THIS ONE!! 1939 Plymouth 2 dr sedan - Late 60s/Early 70s Valiant/Dart donor car used for complete driveline, including dash bezel, gauge cluster & steering. Has the original donar AC, Cruise Control Etc. Someone did a nice job transplanting the items. It even has the front torsion bar suspension. Last owner sadly passed and family had it appraised at around $20k to settle estate. They said Dad drove it in all the local parades etc. I purchased it not running as it sat parked for around 6 years. I cleaned the gas tank & fuel lines. Carb numbers seem to indicate it is a 360ci. I'm not sure, however it started right up after I then put fresh gas in, and drives right along and idles great. The throttle pump in carb did not work so I then rebuilt the carb, and now it doesn't want to idle below 1200 RPMs. I did not tear the carb back apart. It will run down the road fine once moving. The body seems to have been in very nice condition when built, however it does have some roof damage from scraping a low overhead door frame. I'm Terry, Elizabethtown, Pa Please do call or text me at 717.514.4350 with inquiries.
SCROLL DOWN FOR: * COMBO metal lathe, mill, drill * LENCO spot welder * DREIS & KRUMP 8' x 14 gauge Metal Brake * NIAGRA 6' x16 Gauge power sheer * 48" WIDE, Dbl door bead blast cabinet * UNIRAM water borne paint gun cleaner * DVORAK SCOTCHMAN iron worker
3 in 1 COMBINATION LATHE/MILLING/DRILLING MACHINE WITH STAND TOOLING AND ACCESSORIES - $1700 SCROLL DOWN
I purchased this new @ Harbor Freight, and used very little. Combo lathe, mill, drill. Lots of tooling, inside & outside chuck jaws. Steel stand with drawers. Lots of specs on photos. Light surface rust on some bare metal parts, "not pitted" New cost for all included approx $3500, My Price $1700 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
LENCO SPOT WELDER - $550 SCROLL DOWN
Had it many years & always worked well, 230 VOLT, 50 AMP New cost approx. $1500 - My Price $550 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
DREIS & KRUMP 8' x 14 GAUGE BRAKE - $2000 SCROLL DOWN
Had this a long time and still in use. Capacity is 8' long, 14 gauge max. Used similar US Made units are prices around $3000, My Price - $2000 Call or Text Terry, 717.514.4350 Elizabethtown, Pa.
NIAGRA 72" X 16 GAUGE POWER SHEER - $4000 SCROLL DOWN
Still in use, Never failed me, Still cuts sharp & clean, Keep fingers FAR away! Runs on standard 230 volt single phase, Cap. (6 FT.) 72" wide x 16 gauge max. Similar units are hard to find used and a fortune new. Used 5FT. units everywhere & priced at $4500 & up. My Price $4000 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
DVORAK SCOTCHMAN IRON WORKER - $3500 SCROLL DOWN
Most used tool in my shop & still in use. Shows wear, but still works fine, Has square 3/4"ish changeable punch die, and no others included. See photos for specs. Standard 230 volt single phase. Many used on web. Most 3 phase Most not priced, but $4500 & up seems about right. My Price $3500
SANDBLAST CABINET, 48" WIDE, DBL DOOR - $600 SCROLL DOWN
48" Wide, Doors at both ends, Hook shop vac to it for venting. Could use a new glass & some wear parts in gun. Currently still in use. Similar units this big around $2000. My Price $600 Call or Text Terry 717.514.4350 Elizabethtown, Pa.
UNI-RAM WATER BORNE PAINT GUN CLEANER - $400 READ FULL DESCRIPTION PLEASE SCROLL DOWN
Never used this tool. They cost a lot of money. Not sure if it can be used for solvent based paint guns? You see the new cost, so there is lots of $$ room to modify it if a solvent application pump or hoses are needed. My Price $400
BLANK LOT, CHECK BACK!!
BLANK LOT, CHECK BACK!!
Copyright © 2021 Network Solutions, LLC. All rights reserved.